Jump to content

Gateway laptop with SSD not find Vista sp2 wont start PXE-E76


ralphyde
 Share

Recommended Posts

I have a Gateway P-6301 Laptop computer that had a failing hard drive in 2013, which I successfully replaced with a Crucial SSD, then recovered the factory Windows Vista from the recovery partition, then applied all the updates to bring it up to SP-2, and reinstalled my programs, including some that will only run on 32 bit machines (like AmiPro).

 

It has been running flawlessly since then, as I keep it healthy with Malwarebytes Pro and System Mechanic. So it had no malware on it, and was running fine through August 20.  

 

But when I tried to start it on August 21, it got only to the black screen with the cursor in the middle, and stayed that way forever. instead of bringing up the Windows icon and password dialog.  Pressing the start button would shut it down after about 50 seconds.

 

Starting it with PF8 would bring up the repair choices, but Windows would not come up in Safe mode either, nor would command prompt, or directory services.

 

The Repair Computer option, would allow me to access the Gateway System Recovery Options screen showing the following choices: startup repair, system restore, Windows complete PC restore,Windows Memory diagnostic tool, command prompt, and recovery manager.

 

Startup repair ran through several tests all of which came back with code 0x0, then "boot status indicates that the OS booted successfully". and "Startup Repair could not detect a problem."

 

System Restore didn't do anything.

 

The Memory diagnostic tool ran successfully.

 

When I try to startup with PF12, it shows whats happening quickly, and the Error PXE-E76 flashes by "Bad or missing multicast discovery address" Then PXE-M0F "Exiting PXE-ROM"

I tried changing the start device order in the BIOS to no avail.

 

It seems like the link to the part of the strartup routine that puts up the Windows icon and the signon dialog is lost.

 

If all else fails, it appears that I'll have to bite the bullet and do a recovery from the recovery partition, saving data but putting Vista back to 2008 status, then have to update to SP2 again.  I'm hoping there's something easier than that long process..

 

I would appreciate any assistance with this problem.

Thanks 

ralphyde

 

Link to post
Share on other sites

Well, I bit the bullet today, and ran the Windows restore (with saving data option) program from my recovery partition.  It ran flawlessly an installed the 2008 version of Windows Vista, along with 60 associated programs and Windows update.

 

I turned on wi-fi and tried to run Windows Update, to get some of the early updates, with setting of - Let me decide which ones to download and install. I hoped to create smaller more manageable batches to install.  But that old version of Windows Update wouldn't give me anything.

 

I then installed and ran my copy of Malwarebytes Pro to shield the system while on wi-fi, and ran a scan, finding no problems.

 

Now I need to find out how to bring my Windows Vista up to SP2 level.

Can someone please tell me how?  Can I skip the individual fixes and go right to Sp1, and then straight to SP2? And will that give me an updated Windows Update as; well?  I appreciate any knowledge about this.  Thanks.

 

ralphyde

Link to post
Share on other sites

Read post #1 by, Brink, re SP1 : http://www.vistax64.com/windows-updates/140470-why-sp1-may-not-available-you-how-get.html#post653779

 

AFAIK, after SP1 is installed, you should receive notification from Windows Update for SP2.

 

Standalone links for SP2 (installing via WU is preferable) and general info here at post #1 by, Brink : http://www.vistax64.com/windows-updates/229199-download-available-standalone-vista-sp2.html#post1051783

 

I haven't used Vista in a number of years. I do trust, Brink's, info. It might behoove you to do a quick search at that site for other users' experiences.

Link to post
Share on other sites

Successful startup, but two new problems to deal with.  I have also downloaded and installed SP-1  and SP-2 

 

Windows Update has not been working since startup.  It was an old version, 7.0, so I thought a newer version might get around the problem, so I installed the 7.4 agent, since the latest 7.6 wasn't available for downloading and installing.  But with 7.4 agent, I'm still having problems, says it isn't started, though I have put in the recommended settings.

 

The other problem or question is: How to use the BACKUP file from the rebuild run to replace the new (old - 2008) system that was restored.

 

The Recovery from the recovery partition (with saving data) built a folder called BACKUP with folders under the Local Disk (C:) directory entry 

It has the same directory structure as the newly built one all the way down through WINDOWS, with all the previous contents.

 

What I need to know is whether I can just replace the newly built structure with the Backup structure, that would put the computer back the way it was before the problem and would be the ideal solution if it could be done.

 

Thanks for any assistance with either of the two problems

Ralphyde

Link to post
Share on other sites

  • Root Admin

Having downloaded and installed Service Packs would make it just about impossible to do a backup restore unless it was a full backup. A partial or file only or registry only backup would not work well.

If you have a FULL backup you could restore that one and yes it would put it back the way it was before. However one would need to be careful about your own data content as that too could potentially be put back to a previous version or removed. A lot depends on the type of backup and the type of backup software being used. In any case for safety you may want to again manually backup at least all your data files such as images, videos, documents, etc to a different backup drive than the one you've used for your normal backups unless you're confident in what you're doing.

Link to post
Share on other sites

I'm just a home user, maybe someone with more savvy will chime in on this as well.

 

In regards to WU isn't starting (I'm not sure what you meant by "But with 7.4 agent, I'm still having problems, says it isn't started, though I have put in the recommended settings"):

 

Type -- services -- at start menu search. Open (yes to prompt or pass for admin) microsoft management console. This will open Services.

 

Scroll down to WU entry. Does it say it's started under 'status' column? If it's set to manual under 'start up type', right click on the entry, then open the properties window from the list, choose what start-up type you wish, (I use automatic delayed), click apply, ok etc...reboot.

 

You can start the service manually there as well by the same right clicking then choosing 'start'.

 

If more problems, try running the 'sfc/' command that's applicable to you. I'd start with verify only. You could be having trouble with 1 or more of WU's dependencies.

 

Beyond that -- there is a 'fixit(s)' available at MS specifically for WU.

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
Back to top
×
×
  • Create New...

Important Information

This site uses cookies - We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.