Jump to content

Malware Removal PUM.Hijack


WarWarp
 Share

Recommended Posts

Welcome to the forum.

Please download and run RogueKiller 32 Bit to your desktop.

RogueKiller 64 Bit <---use this one for 64 bit systems

Which system am I using?

Quit all running programs.

For Windows XP, double-click to start.

For Vista or Windows 7-8, do a right-click on the program, select Run as Administrator to start, & when prompted Allow to run.

Click Scan to scan the system.

When the scan completes > Close out the program > Don't Fix anything!

Don't run any other options, they're not all bad!!!!!!!

Post back the report which should be located on your desktop.

(please don't put logs in code or quotes and use the default font)

General P2P/Piracy Warning:

1. If you're using Peer 2 Peer software such as uTorrent, BitTorrent or similar you must either fully uninstall it or completely disable it from running while being assisted here.

Failure to remove or disable such software will result in your topic being closed and no further assistance being provided.

2. If you have illegal/cracked software, cracks, keygens, custom (Adobe) host file, etc. on the system, please remove or uninstall them now and read the policy on Piracy.

Failure to remove such software will result in your topic being closed and no further assistance being provided.

MrC

Note:

Please read all of my instructions completely including these.

Make sure system restore is turned on and running

Make sure you're subscribed to this topic: Click on the Follow This Topic Button (at the top right of this page), make sure that the Receive notification box is checked and that it is set to Instantly

Removing malware can be unpredictable...unlikely but things can go very wrong! Backup any files that cannot be replaced. You can copy them to a CD/DVD, external drive or a pen drive

<+>Please don't run any other scans, download, install or uninstall any programs while I'm working with you.

<+>The removal of malware isn't instantaneous, please be patient.

<+>When we are done, I'll give to instructions on how to cleanup all the tools and logs

<+>Please stick with me until I give you the "all clear" and Please don't waste my time by leaving before that.

------->Your topic will be closed if you haven't replied within 3 days!<--------

(If I don't respond within 24 hours, please send me a PM)

Link to post
Share on other sites

Run RogueKiller again and click Scan

When the scan completes > click on the Registry tab

Put a check next to all of these and uncheck the rest: (if found)

 

[HJ POL][PUM] HKCU\[...]\System : DisableTaskMgr (1) -> FOUND

[HJ POL][PUM] HKCU\[...]\System : DisableRegistryTools (1) -> FOUND

Now click Delete on the right hand column under Options

-------------

Then........

Download Malwarebytes Anti-Rootkit from HERE

  • Unzip the contents to a folder in a convenient location.
  • Open the folder where the contents were unzipped and run mbar.exe
  • Follow the instructions in the wizard to update and allow the program to scan your computer for threats.
  • Click on the Cleanup button to remove any threats and reboot if prompted to do so.
  • Wait while the system shuts down and the cleanup process is performed.
  • Perform another scan with Malwarebytes Anti-Rootkit to verify that no threats remain. If they do, then click Cleanup once more and repeat the process.
  • When done, please post the two logs produced they will be in the MBAR folder..... mbar-log.txt and system-log.txt
To attach a log if needed:

Bottom right corner of this page.

reply1.jpg

New window that comes up.

replyer1.jpg

~~~~~~~~~~~~~~~~~~~~~~~

Note:

If no additional threats were found, verify that your system is now running normally, making sure that the following items are functional:

Internet access

Windows Update

Windows Firewall

If there are additional problems with your system, such as any of those listed above or other system issues, then run the fixdamage tool included with Malwarebytes Anti-Rootkit and reboot. It's located in the Plugins folder which is in the MBAR folder.

Just run fixdamage.exe.

Verify that they are now functioning normally.

MrC

Link to post
Share on other sites

Due to the lack of feedback this topic is closed to prevent others from posting here. If you need this topic reopened, please send a Private Message to any one of the moderating team members. Please include a link to this thread with your request. This applies only to the originator of this thread.

Other members who need assistance please start your own topic in a new thread. Thanks!

Link to post
Share on other sites

Guest
This topic is now closed to further replies.
 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
Back to top
×
×
  • Create New...

Important Information

This site uses cookies - We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.